Home » Products » Painting Products » Coatings Inspection Instruments

Coatings Inspection Instruments

We offers a variety of Inspection Tools and Instruments for Quality Control.Our partners specialize in the design and manufacture of a complete range of instrumentation and test methods for coating process control.

Concrete Covermeters

This easy to use gauge not only quickly and accurately identifies the location,
orientation, depth and diameter of both high tensile steel and stainless steel
rebar within concrete, but also the potentlol for corrosion.

  • MATERIAL THICKNESS GAUGE
  • SURFACE PROFILE
  • SURFACE CLEANLINESS
  • CLIMATIC CONDITIONS
  • COATING THICKNESS
  • ADHESION TESTER
  • PINHOLE & POROSIT
  • WELDING GAUGE

Elcometer 127 Keane- Tator Surface Comparators & Magnifier

The Elcometer 127 range of Surface Comparators are available in sand, shot or grit surface profiles. Each comparator is supplied with 5 profile grades ranging from 0.5 - 5.5mils. Designed for use with the Elcometer 127 illuminated magnifier, each comparator has a hole in the centre allowing for clear visual comparisons to be made.

• 5 Roughness Values per Comparator

Elcometer 122 Testex Tape

Elcometer 122 Testex Tape consists of foam with a non-compressible backing. The foam side is rubbed into the surface providing a permanent mould of the peak-to-valley profile, which can then be measured using the Elcometer 124 Thickness Gauge."Y Elcometer 122 Testex Tape is available in three profile ranges. It is important that the tape grade chosen is reflective of the profile being measured, as using tape grade below the actual value may provide a "false" reading.
There are 50 tests in each roll.

Elcometer 123 Surface Profile Gauge

This easy to use gauge measures the peak-to-valley height of a blast cleaned surface.

The average of a series of measurements provides an indication of the surface roughness and allows the surfaces to be compared as blasting proceeds.

• Metric and Imperial versions

Elcometer 124 Thickness Gauge

The Elcometer 124 Thickness Gauge is used to measure the peak-to-valley height of a surface profile moulded in the Elcometer 122 Testex Replica Tape.

• Available in both Metric and Imperial versions.

• Quick and easy to use.

• Anvil pressure as required in the Standards.

Elcometer 116 Whirling & Sling Hygrometers

These instruments are designed to determine the dewpoint and relative humidity at any given time. The Elcometer 116A Whirling Hygrometer is available in Celsius scale. A guide for Relative Humidity (RH) determination is supplied with each instrument and the dewpoint can accurately be obtained using the Elcometer 114 Dewpoint Calculator. The Elcometer 116C Sling Hygrometer, shown as the black unit in the photograph, is a convenient, self contained instrument with an inbuilt slide rule for the calculation of %RH and dewpoint. It has spirit filled thermometers and is available in °C or of scales.

• Manual operation, no power supply required

• Spirit filled thermometers

Elcometer 223 Digital Surface Profile Gauge

A Digital Surface Profile Gauge which measures the peak-to-valley height of a surface in a similar way to the Elcometer 224.

• RS232 output - for direct transfer of readings to a Pc' datalogger,miniprinter etc. This provides a permanent record of your test results as thereis no memory in the gauge.

• Metric and Imperial switchable.

FAMB Half-Mask

Continuous flow respirator that accommodates low
pressure air sources canbe worn with faceshields,visors,
welding helmets and hard hats

Respiratoey & Air Quality Products

Spectrum Full Facepiece

Available as a continuous
flow or pressure demand respirator.
Can be equipped with an escape cylinder

Supplied Air Respirators

CC20 Series Hoods

Appropriate for painting,
chemical handling, healthcare and
pharmaceutical applications.

GR50 Series Nomex Painting Hood

Lightweight and fully protective
outer hood and inner flame
retardant protective barrier.

88vx Series Abrasive Blasting Helmet

Full head, neck and torso protection.
Superior protection for abrasive blasters and painters.

Rpb offers totally configured work systems for use in a wide variety of applications - from painting and abrasive blasting to pharmaceutical and chemical manufacturing. Everything you need for effective respiratory protection is provided in one complete package.

Powered Air-Purifying Respirator

The PA30lS helps provide respiratory protection to workers in many potentially explosive atmospheres. Vapors from organic solvents and high dust concentrations can be triggered from a spark by equipment. The intrinsically safe PA30lS Powered Air-Purifying Respirator is designed exactly for these types of environments.

Highlights

  • NIOSH approved for HE, OVAGHE and NBC
  • Seven-hour battery run time
  • Low battery alarm alerts wearer before protection is lost
  • No battery cable that can be unplugged accidentally

Applications

Painting and Coatings Operations Pharmaceutical Manufacturing

GracoDevilbissSpeedcoRpbElcometerSintoMullenbach3MVvq